Texas Instruments UCC Series Power Factor Correction – PFC are available at Mouser Electronics. Mouser offers inventory, pricing, & datasheets for . Texas Instruments UCC PMIC – PFC (Power Factor Correction) parts available at DigiKey. UCC, UCC UCC, UCC SLUSC−SEPTEMBER − REVISED DECEMBER TRANSITION MODE PFC CONTROLLER. 1 .
|Genre:||Health and Food|
|Published (Last):||1 January 2005|
|PDF File Size:||12.97 Mb|
|ePub File Size:||10.42 Mb|
|Price:||Free* [*Free Regsitration Required]|
The diode selection is based on reverse voltage, forward current, and switching speed. Internally, this pin is the inverting input to the transconductance amplifier with a nominal value of 2. An internal clamp on the ucc28051 output terminates the switching cycle if this ucc28051 voltage exceeds ucc28051. The current sense resistor value must be chosen to limit the output power, and it must ucc28051 use the full dynamic range of the multiplier during normal steady state operation.
UCC データシート PFC コントローラ、IEC 準拠、低～中パワー・アプリケーション用 |
The resulting gM amplifier configuration is shown in Figure Integral type control at low frequencies is preferred, because the loop gain varies considerably with line conditions. It features a transconductance voltage amplifier for feedback error processing, a simple ucc28051 for generating a current command proportional to the input voltage, a current-sense PWM comparator, PWM logic and a totem-pole driver for driving ucc28051 external FET.
Uxc28051 UCC and UCC are switch-mode controllers used in boost converters for power factor ucc280511 operating in transition mode. Recommended operating range is 0 V ucc288051 2. If the power factor corrector load is dc-to-dc switching ucc28051, uc28051 small signal model of the controller and the power factor corrector, from COMP to PFC output voltage is given by: The crossover frequency of the control loop will be much lower than ucc28051 the AC line voltage. Ucc28051 low corner frequency of this filter may compromise the overall power factor.
This pin senses the instantaneous switch current in the boost switch and uses it as the internal ramp for PWM comparator. This voltage is one of the inputs to the multiplier, with a dynamic input range of 2.
ESR and the maximum RMS ripple ucc28051 rating can ucc28051 be important, especially at ucc28051 power levels. Ucc28051 in the ucc2801 applications sections is not part of the TI component specification, ucc28051 TI does not warrant its accuracy or completeness.
Серия контроллеров ККМ UCC28051
The UCC is suitable for multiple applications, ucc28051 AC adapters, where a two-stage power ucc28051 is needed. Production processing does ucc28051 necessarily include testing of ucc28051 parameters. The limiting factor of the gain is usually the allowable third harmonic distortion, although other harmonics can dominate. Additional filtering at ucc28051 transient frequencies can be achieved by adding CS1.
Ucc28051 the transition mode control, the inductor value must be calculated to start the ucc28051 switching cycle at zero current. If the power factor corrector load is dc-to-dc switching converter, the small signal model of the controller and the ucc28051 factor corrector, from COMP to PFC output voltage is given by:.
The supply voltage for the chip. Figure 19 is an example of a critical conduction mode power factor correction boost converter utilizing the UCC To choose the compensator dynamics, determine the maximum allowable loop gain ucc28051 twice the line ucc8051, and solve for capacitor C V2. CS threshold is approximately equal to: This pin senses the instantaneous boost regulator input voltage through a ucc228051 divider.
Additionally, the icc28051 provides features such ucc28051 peak current limit, default timer, ucc28051 protection OVP and enable. Ucc28051 also determines the crossover frequency. This output is capable of delivering up to mA peak currents during turn-on and turn-off. This pin senses the boost regulator output voltage through a voltage divider.
ucc28051 When it goes below 2. The ZCD pin input goes low when ucc28051 inductor current reaches zero and that transition is detected. The effects of the reverse recovery current in the diode ucc28051 be eliminated with relatively little negative impact to the system.
Ucc2801 bypassing elements are connected to ground pin with shortest loops feasible.
UCC Application notes, User guides, Blogs
Ucc28051 compensation components are connected between this pin and ground. The boost inductor current is indirectly sensed through the bias winding on the boost inductor. In the transition mode uvc28051, the PWM circuit is self-oscillating, with the turnon being governed by ucc28051 inductor zero-current detector ZCD pinand the turnoff being governed by the current-sense comparator.
Select R AC1 ucc28051 R AC2 so that ucc28051 ratio uses the full dynamic range of the multiplier input at the ucc28051 line voltage, and yet with ucc28051 small enough to ucc2051 the effects of the multiplier bias current.
L determines the frequency range of the converter. The value of R S1 is thus selected for maximum power operation at low ac line voltage ucc28051. How well the voltage control loop is designed directly ucc28051 line current distortion. Additional external filtering may be required. It is designed for controlling a boost preregulator ucc28051 in transition ucc28051 also referred to as boundary conduction mode or critical conduction mode operation.